Honda Fit/Jazz - Power Window Master Switch Input Test
Power Window Master Switch Input Test
NOTE: The power window control unit is built into the power window master switch, and it only controls the driver's window operations.
1. | Remove the power window master switch (A).
|
2. | Disconnect the 20P connector (B) from the master switch.
|
3. | Inspect the connector and socket terminals to be sure they are all making good contact.
- If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
- If the terminals look OK, make the following input tests at the connector.
- If a test indicates a problem, find and correct the cause, then recheck the system.
- If all the input tests prove OK, go to 4.
|
4. | With the connector still disconnected, make these input tests at the connector.
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If all the input tests prove OK, go to 5.
Cavity | Wire | Test condition | Test: Desired result | Possible cause if result is not obtained |
---|
46 | BLK | Under all condition | Check for continuity to ground: There should be continuity. | - Poor ground (G401)
- An open in the wire
| 82 | 14 | GRN/WHT | Under all conditions | Check for voltage to ground: There should be battery voltage. | - Blown No. 29 (20A) fuse in the under-dash fuse/relay box
- An open in the wire
| 5 | GRN | Ignition switch ON (II) | Check for voltage to ground: There should be battery voltage. | - Blown No. 10 (10A) fuse in the under-dash fuse/relay box
- Blown No. 15, 16 or 17 (20A) fuse in the under-dash fuse/relay box
- Faulty power window relay
- An open in the wire
| 28 | GRN/BLK | 18 | YEL/RED | 11 | YEL/BLU | 64 | RED/YEL | Connect the No. 14 and No. 6 No. 4 terminals, and the No. 7No. 3and No. 4No. 6terminals, and turn the ignition switch ON (II). | Check for driver's window motor operation: It should run (the driver's window moves down). | - Faulty driver's window motor
- An open in the wire
| 73 | RED/BLK | 19 | BLU/RED | Connect the No. 2 and No. 3No. 7 terminals, and the No. 1No. 9 and No. 8No. 2terminals, and turn the ignition switch ON (II). | Check for front passenger's window motor operation: It should run (the front passenger's window moves down). | - Faulty front passenger's window motor
- Faulty front passenger's window switch
- An open in the wire
| 37 | BLU/WHT | 19 | BRN/WHT | Connect the No. 18 and No. 17 terminals, and the No. 19 and No. 8No. 2 terminals, and turn the ignition switch ON (II). | Check for left rear window motor operation: It should run (the left rear window moves down). | - Faulty left rear window motor
- Faulty left rear window switch
- An open in the wire
| 17 | BRN | 12 | BLU/ORN | Connect the No. 11 and No. 10 terminals, and the No. 12 and No. 8No. 2terminals, and turn the ignition switch ON (II). | Check for right rear window motor operation: It should run (the right rear window moves down). | - Faulty right rear window motor
- Faulty right rear window switch
- An open in the wire
| 10 | BRN/YEL |
|
5. | Reconnect the 20P connector to the switch, and perform the following input tests.
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If all the input tests prove OK, the control unit must be faulty; replace the power window master switch.
Cavity | Wire | Test condition | Test: Desired result | Possible cause if result is not obtained |
---|
16 | RED/WHT | Ignition switch ON (II) | Check for voltage to ground: There should be battery voltage. | - Faulty power window master switch
- An open in the wire
| 91 | LT GRN | Under all conditions | Check for voltage to ground: There should be battery voltage. | | 20 | BLU | Ignition switch ON (II), and the driver's window switch AUTO DOWN | Check for voltage between the No. 20 and No. 9No. 1terminals: There should be 0 V-about 5 V-0 V-about 5 V repeatedly. | - Blown No. 29 (20A) fuse in the under-dash fuse/relay box
- Faulty power window relay
- Faulty power window master switch
- An open in the wire
| 13 | ORN | Ignition switch ON (II), and the driver's window switch AUTO DOWN | Check for voltage between the No. 13 and No. 9No. 1terminals: There should be 0 V-about 5 V-0 V-about 5 V repeatedly. |
|
Honda Fit/Jazz 02-05 Workshop Manual
Back to all Manuals